Argox PT-10 Uživatelský manuál Strana 1

User’s Manual PT-10/PT-12 Portable Data Collectors DOC NO. UM-PT105-01 Oct. 2006 Version 2.0

6 3.1.2 Cradle Dimensions of CRD-10 Cradle 130mm (L) x 100mm (W) x 67.6mm (H) Details of CRD-10 Cradle

7 4. Serial and Charging Connector To connect with the multiple function socket on the collector for data transmission and char

8 3.2 Handling Precautions To avoid malfunctioning and to ensure years of trouble free operation, pay attention to the follow

9Use of the collector Avoid temperature changes. Sudden temperature changes can cause condensation to form on the collector.

103.3 Assembly Follow the next steps to make your collector ready for installation in a system that is described further in th

11 3.3.2 Cradle Power Connection 1. Attach the DC jack of the AC adapter into the socket of the cradle. Then connect the AC

12 3.4 Installing, Replacing and Charging Batteries Wrong use of batteries might cause serious damage to the collector or to t

13 Main Battery The main battery can consist of: 1. Argox rechargeable battery pack (Ni-MH) (Ref. 1) To be recharged when plac

14 How to charge Argox rechargeable battery pack in the cradle 1. Make sure that the Argox rechargeable battery pack is insert

15 3. Change a full Argox battery pack for PT-12 directly, and push it back to the collector with correct direction (Ref. 2).

II CAUTION: This user’s manual may be revised or withdrawn any time without prior notice. Copyright 2005, Argox Information

163.5 Installing in a System Exercise caution at all times when working with AC-powered equipment. Turn off your devices

17 3.5.2 Via CRD-10 Cradle The CRD-10 cradle provides two methods for data transmission: through an RS-232 cable (9-pin connect

18 4. Operation of the Collector 4.1 Software Description The functionality of the collector is determined by software, e.g.

194.2 Hardware Description 4.2.1 Display Description The pixel number of the LCD display is 128 dots (W) * 64 dots (H). The

20 4.2.2 Keypad Description The PT Series keypad consists of 22 rubber keys including one trigger key. Key Define Function S

21  Available function key combinations Any-time condition: + [0]: Back Light Setting + [1]: LCD Contrast Setting + [2]: Be

22 4.2.6 Splashed Logo Description  If there is no user-defined logo, the default logo in the system will be displayed. Use

23 4.3.2 Power on by using hot key When the collector is off, user can press PW key and other special keys together to start H

24 4.4 Main Menu Structure The main menu will be available only under Standard Mode. Please see the structure and function as

25 4.4.1 Applications Function User can execute a designed program and proceed to collect and store data based on the demand

III Table of Content 1. INTRODUCTION...

26For example, if you want to get an “H”, just continuously press key TWICE under Alpha Mode and you will get “H” after about

27 4.4.3 System Tools 4.4.3.1 Scan Test  User can make a scanning test by this function. When a bar code was read successf

284.4.4 Setting 4.4.4.1 BIOS Setting Enter from Setting\BIOS Setting. The options were listed as below: Item Parameter Ran

29Read Confirm None Beep LED Both Both Set up the notice options when the scanner read and decode a bar code. None – without not

30 4.4.4.2 Boot Configure Mode Setting: This is used to set up the mode to standard Mode or Program Mode when power on. Prog

31 5. Scanning Please take care of the handling precautions. Please make sure that the collector is installed according to

32 Point the LED lightbeam to barcode as shown in the scan position illustration.  The barcode will be read and the reading

33 6. Cable Pin-out 6.1 RS232 Cable for PT-10 / PT-12 (9-pin to 10-pin) 10 PIN / 1.25mm Connector 9PINS / D-Sub Female T

34 6.2 RS232 Cable for CRD-10 Cradle (9-pin to 9-pin) 9 PIN / D-Sub Male Type 9 PIN / D-Sub Female Type Connector for CRD-1

35 7. Trouble Shooting This chapter contains information on solving problems you may encounter when using the collector and/or

IV 5. SCANNING... 31 5.1

36 Data is corrupted, or no data is transmitted  Is the proper baud rate selected? The computer needs the same baud rate as

37 7.4 Collector Problems Collector does not respond to key press while the display stays on Message “No Programs…” is show

38 8. Product Ordering Information Item Model Name Description 1 PT-10 PT-10 portable collector unit 2 PT-12 PT-12 portab

1 1. Introduction The PT series portable data collector (PDC) is well suited for a variety of portable applications. It has a

2 2. Specifications Feature PT-10 PT-12 CPU/Memory OS Proprietary CPU 32-bit RISC Processor with ARM core RAM 1M SRAM 2M S

3 Power supply Main power 2 x AA Alkaline battery rechargeable Ni-MH battery pack Back up power 3V rechargeable Lithium bat

4 3. Getting Started 3.1 Detailed View 3.1.1 Collector Dimensions of Collector 140mm (L) x 67mm (W) x 25.7mm (H) Details

5 3. LCD Display For displaying information and battery status Battery Indicator Battery Full 2/3 Battery Life 1/3 Battery