Argox G-6000 Uživatelský manuál

Checking Your Box Receiving the box of your printer, you are advised to check first for the possible shipping damage. There are two ways you can d

Cutter Mode Follow the common procedure of “ Loading the Media “ of Standard Mode from step 1 to 3. 4. Insert the media into the print head module

Operator Controls LED Indicators Front Panel There are three LED indicators on the front panel, “READY”, “MEDIA” and “RIBBON”. These indicators di

Buttons LCD Display Basic Functions : There are three buttons, each having two basic functions. Button Under normal condition Pressed the butt

Setting from Panel Selection Items Item Range Factory Default Remarks CUT/PEEL POS (mm) -15 ~ 15 mm 0 mm Controls cut and peeling position. PRIN

characteristics. Once you change it make sure to make calibration before printing. BACK FEED DISABLED, ENABLED DISABLED BACK DISTANCE 10~40 mm 0 mm

Rear Panel Printing Configuration Report The rear panel includes Performing the Self Test - An 8-bit DIP switch - A 36-pin parallel port 1. Tu

Printing Configuration Report Returning to Factory Default Settings Performing the Self Test If you would like to reset the printer to its factor

Hooking up the Printer & Computer Communicate with the Printer Connecting the Printer to Your Host Communicate with the Printer 1. You can

Installing Driver Notes: 1. If you are just updating your driver, make sure to delete the previous version first. Note: Before installation, pleas

Set the Parameters For Win 98 After installing the driver, you can follow the path below to set parameters: ❑ Ports Properties menu Æ click “Deta

Power Supply Setting up the Printer Before setting up the printer you should first consider the following: ♦ ♦ ♦ Find a solid flat surface with a

❑ Output bin 40❑ Create User-Define Paper (Accessory setting) Properties menu Properties menu Æ click "Paper" Æ click "Paper"

For Win 2000 42❑ Orientation ❑ Ports Printing Reference menu Properties menu Æ click "Layout" Æ click "Ports" Æ select &qu

❑ Create a new size Printer menu Æ right click to get pop-up menu in blank space Æ select "Server Properties" Æ enter a form name for th

For Win XP ❑ Paper/Output (Speed) ❑ Ports ❑ Print quality (Darkness) Properties menu → Click "Ports". Default Document menu → S

48 ❑ Orientation ❑ Create a new size Printing Reference menu Printer menu → Click "Layout". → Right click to get → Select "Por

Troubleshooting B. Problems on ribbon Blinking Indicators READY and RIBBON LCD display RIBBON OUT Generally, when a malfunction or an abnormal co

Vertical streaks in the printout usually indicate a dirty or faulty print head. Clean the print head first, if they still persist, replace the print

Caring for your Printer In order to continue your print jobs after any abnormal conditions have been recovered, simply press the CANCEL button or rest

Reference Technical Information 1. General Specification Specification Model G-6000 Print method Direct thermal and thermal transfer Resolution

2. Fonts, Bar Codes and Graphics Specification 3. Interface Specifications Introduction The specifications of fonts, bar codes and graphics depend

Parts and Features LCD Display Top Access DoorFront Access Door 6 Head Latch Paper Sensor Guide Platen Roller Thermal Print Head Therma

Connection with host: The most simple way to connect to other hosts (not PC compatible) or terminals is: Host 25S Printer 9P Host 9S

4. ASCII TABLE Parallel (Centronics) 62 0 1 2 3 4 5 6 70 NUL 0 @ P ` p1 SOH XON ! 1 A Q a q2 STX “ 2

Appendix A: Printer Status Appendix B: Installation for Cutter LCD display Blinking LED Description PAUSE READY The printer is at pause stat

6. Loosen two screws (4) from bracket (5). , 7. Insert the left side of cutter bracket (7) and secure two screws (6) to the TPH modul

Appendix C: 5. Connect the dispenser sensor to JP12 (LABEL) of main board and secure the dispenser board in front of TPH module. Installation for

Calibration for Dispenser Sensor Adjustment If you find the sensor is not so sensitive or mis –detection you can send two commands to calibrate it.

Important Safety Information SAFETY INSTRUCTIONS 1. Please read these safety instructions carefully. 2. Please keep this User‘s Manual

Loading the Ribbon Reminder Notes: Peeler Sensor 1. This section is applicable to the transfer thermal printing. 2. Attached r

BracketHead Latch 2 Ribbon Supply Spindle 3 10Bare CorePrint Head Module Ribbon Pick-upSpindle 54 9

7Bracket Outside Media Guide Head Latch6Media Supply Spindle Media GuideLoading the Media G-6000 printers can be operated in three different

Print Head ModulePaper Sensor Guide8 9 Head Latch Bracket Outside Media Guide 13 14

Peel Off Mode Follow the common procedure of “ Loading the Media “ of Standard Mode from step 1 to 3. 4. Remove approximately 6” long labels from

1513 Rewinder Kit Print Head Module 1614 Sticker Rewinder Kit 17 18